Click and drag to rotate
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC) 3d printed
Supplier NVG6, Hull (1:200, RC) 3d printed

DIGITAL PREVIEW
Not a Photo

Supplier NVG6, Hull (1:200, RC)

Print With Shapeways
Choose Your Material
$90.31
Choose your color and finish
QTY

Have a question about this product?

contact the designer
You must be logged in and verified to contact the designer.
Product Description
Parts in "Strong & Flexible" material to complete the model of the historic German supply vessel "NVG 6 Holstentor" in 1:200 scale:
  • hull

To complete the ship, four different sets of 3D prints are needed:
A display stand is currenctly not available (yet).

Size of the model:
  length:      26.4 cm
  width:         5.5 cm

NVG 6 was built in 1966 as one of the first supply vessels to support the offshore activities in the North Sea, and it was run by DDG Hansa. Many of the following supply vessels were derived from this design. After 1967, the vessel was named „Holstentor“, and while it was sold later, it was operated until 2012, last as „Mardive III. 

Technical data of the original:
  length:        52.9 m
  width:         11.3 m

The Model is designed in 1:200 scale. It can be built as a model for static display or as a working RC boat. It is set up to enable radio control functions (RC), driven by the twin shaft propulsion. The rudder and the bow thruster are not prepared for any RC function due to the very low weight of the model. As the model is rather small, the model can only be used in very quiet water conditions. However, this model is not set up to be ready to run, it requires refinement and is only suitable for skilled model builders. The aft deck of the model can be planked with real wood veneer. The model is prepared accordingly. An assembly manual, a set of drawings and further informations can be found on my website (download section): http://www.microboathobby.com/  

To complete the RC model, additional components are needed:
  • two motors M700 or M700L (DC Ø 7mm x 15mm) for main propulsion
  • two shafts (1mm diameter) with stern tubes (2mm diameter) and props (max. 10mm diameter)
  • RC equipment of your choice


More information on the original is available on e.g. the following ressources:
 
Details
What's in the box:
Supplier NVG6, Hull (1:200, RC)
Dimensions:
26.38 x 6 x 3.92 cm
Switch to inches
10.39 x 2.36 x 1.54 inches
Switch to cm
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.