6-Camera Rig
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$290.79
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
The "Adaptive Rig System" is designed for Gopro Hero4 (or Hero3) that have been modified to receive a super wide angle lens(between 190-Degree and 220-Degree for best results)
The "Adaptive Rig System" is modular. Once mounted in the "Camera cages", the Gopro cameras can be installed either on the 3, 4 or 6-camera base(2 and 8 camera bases in preparation, prototypes available for printing at Shapeways on special request).
The "6-camera Rig" presented here is composed of:
-one 3d-printed camera base (6-cam configuration)
-Six 3d-printed camera cages
Screws and nuts needed to assemble the 6-camera rig (External Ebay links provided):
-3mm/M3x0.5 - Socket Head Cap screws - 30mm long - Qty needed 18 (3 per camera)
-3mm/M3x0.5 - Hex Nuts - Qty needed 30 (5 per camera)
-3mm/M3x0.5 - Flat Head Socket screws countersunk - 12mm long - Qty needed 12 (2 per camera)
Already modified Gopro cameras can be bought directly from Peau productions
Otherwise DIY lens installation can be done easily on stock Gopro cameras.
Many videos are available on Youtube to show the lens replacement process.
(See also this step-by-step instructions by Izugar)
220-degree lenses can be purchased from Peau Productions, Ebay or Aliexpress
190-degree lenses can be found on Aliexpress
The 6-camera configuration with Gopro Hero4 Black edition can achieve a video ouput resolution of up to 6K per eye in 3D(Stereoscopic) at 30fps. Photo resolution up to 3k x 6k.
In 2D mode(monoscopic), comparable resolutions can be achieved with the benefit of ample overlap between cameras, allowing more precise stitching.
All rigs have a 1/4" hole clearance in the center, for tripod or grip mounting.
The camera cages have been designed to allow good heat dissipation and an access to all buttons and connectors, including the rear 30-pin bus connector, that can be used to power the cameras from an external source, via a Battery Eliminator cable. This product and/or service is not affiliated with, endorsed by or in any way associated with GoPro Inc. or its products and services. GoPro, HERO and their respective logos are trademarks or registered trademarks of GoPro, Inc.
The "Adaptive Rig System" is modular. Once mounted in the "Camera cages", the Gopro cameras can be installed either on the 3, 4 or 6-camera base(2 and 8 camera bases in preparation, prototypes available for printing at Shapeways on special request).
The "6-camera Rig" presented here is composed of:
-one 3d-printed camera base (6-cam configuration)
-Six 3d-printed camera cages
Screws and nuts needed to assemble the 6-camera rig (External Ebay links provided):
-3mm/M3x0.5 - Socket Head Cap screws - 30mm long - Qty needed 18 (3 per camera)
-3mm/M3x0.5 - Hex Nuts - Qty needed 30 (5 per camera)
-3mm/M3x0.5 - Flat Head Socket screws countersunk - 12mm long - Qty needed 12 (2 per camera)
Already modified Gopro cameras can be bought directly from Peau productions
Otherwise DIY lens installation can be done easily on stock Gopro cameras.
Many videos are available on Youtube to show the lens replacement process.
(See also this step-by-step instructions by Izugar)
220-degree lenses can be purchased from Peau Productions, Ebay or Aliexpress
190-degree lenses can be found on Aliexpress
The 6-camera configuration with Gopro Hero4 Black edition can achieve a video ouput resolution of up to 6K per eye in 3D(Stereoscopic) at 30fps. Photo resolution up to 3k x 6k.
In 2D mode(monoscopic), comparable resolutions can be achieved with the benefit of ample overlap between cameras, allowing more precise stitching.
All rigs have a 1/4" hole clearance in the center, for tripod or grip mounting.
The camera cages have been designed to allow good heat dissipation and an access to all buttons and connectors, including the rear 30-pin bus connector, that can be used to power the cameras from an external source, via a Battery Eliminator cable. This product and/or service is not affiliated with, endorsed by or in any way associated with GoPro Inc. or its products and services. GoPro, HERO and their respective logos are trademarks or registered trademarks of GoPro, Inc.
Details
What's in the box:
6-Camera Rig(1)
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
